|
1”weaver aluminum AR
Stanag riser mount |
|
GSE Handguard Pistol Grip Mount |
|
GSE A2 Z-RAIL |
|
Mounts on A2 carry handle and extends across top of
carbine handguards. |
$69.95
|
|
FIRE System Rails - Standard &
Scout |
|
These two GG&G FIRE System rails were
designed to mount easily over the integral rails of the
M16/AR-15 flat top receiver and work in conjunction with
our MAD or A2 Style BUIS flip-up rear sights. As they
raise the line of sight by ½- inch, they offer a proper
cheek weld when optical devices are attached. In
addition, they serve to protect the flat top receiver’s
integral rails from the wear associated with
quick-release-type mounts. The Scout length rail extends
2 inches beyond the handguards and clears the M4
forearm. It was developed to accommodate long-eye-relief
“scout”-type scopes and also Aimpoint red dot sights
with night vision monoculars mounted to their rear. The
standard length rail has been employed mainly as a riser
for conventional optical sights. Manufactured from 6061
T6 aluminum alloy, black hard-coat anodized, all of the
GG&G FIRE System rails meet MIL-STD-1913. These rails
lock onto the flat top receiver by means of a locking
side bar and two socket head screws. This provides both
a positive and perfectly aligned lock-up even on
well-worn receiver rails. The socket head wrench
required for installation is included. |
FIRE System
Standard Length Rail
-
$75.00
FIRE System Scout
Length Rails $82.95
|
|
FIRE System GS-1 Rail
|
|
Our GS-1 FIRE System rail was
designed for mounting a conventional-type scope on the
M16/AR15. It provides significantly longer eye relief
for a proper scope/operator interface and the capability
of attaching additional optical devices, such as a night
vision monocular. The back of the rail has been tapered
to blend with the rear of the upper receiver and is not
designed to mount a BUIS flip-up rear sight. It extends
3 inches over the handguards and clears the M4 forearm.
Manufactured from 6061 T6 aluminum alloy, black
hard-coat anodized, the GS-1 rail meets MIL-STD-1913. As
with the other FIRE System rails, it locks onto the flat
top receiver by means of a locking side bar and two
socket head screws. It’s available, on request, with 20
MOA of elevation built in. |
$89.95
|
|
M3 Tactical Illuminator Light Rail
Adapter For Dovetails |
|
Our new M3 Tactical Illuminator
adapter rail for dovetail installation on such systems
as the Knight Armaments Company’s “RIS” or “RAS”
forearms or the D.S. Arms rail units for the FN FAL
series can be easily installed and provides a solid and
sturdy mounting base for the M3. This clever squeeze
rail design will also fit on mil spec 1913 and other
“Weaver”-type dovetails. Both the adapter rail and the
M3 Tactical Illuminator can be easily installed or
removed. This new GG&G adapter is manufactured from 6061
T6 aluminum and is hard-anodized matte black. |
$35.00
|
|
Offset Tactical Flashlight Mount
For Use With Vertical Foregrip |
|
The hit probability of any
shoulder-mounted, selective-fire weapon can be greatly
increased by installation of a vertical foregrip, as
weapons of this type are often deployed in the full auto
mode, especially at distances under 15 yards. In
addition, flashlights attached to shoulder-mounted
weaponry are a requirement for urban warfare. Without
doubt, an illumination device is a very important
accessory. Until now, attempting to use a tactical
flashlight in conjunction with a vertical foregrip
resulted in three scenarios: 1. Purchase an expensive
combination vertical foregrip/flashlight. 2. While
trying to maintain a grip on the vertical foregrip,
attempt an uncomfortable and dangerous rotation of the
grip hand to try to get the thumb high enough to engage
the rear of the flashlight typically mounted at the
three o'clock or nine o'clock position (strong left
shooter). 3. Use an expensive and somewhat messy pig
tail with a pressure pad glued to the foregrip.
GG&G’s staff has solved the problem of interfacing a
vertical foregrip with a weapon-mounted flashlight in an
ingenious manner. The Offset Tactical Flashlight
Mount For Use With Vertical Foregrips places the M3
or other tactical flashlight, offset to the right or
left of the weapon’s forearm at about 5 o’clock or 8
o’clock, respectively. This permits the operator to
manipulate with the thumb, the M3 Illuminator’s rocker
switch or rear pressure button of other tactical
flashlights such as many within the Surefire line, while
the support hand remains solidly on the vertical
foregrip. The Offset Tactical Flashlight Mount For
Use With Vertical Foregrips comes complete with both
rails. The M3 mounting rail can be easily removed and a
short section of MIL-STD-1913 rail installed for
attaching a SUREFIRE or other small flashlight by means
of a standard ring. The mounting rails are fully
interchangeable.
|
Offset Tactical
Flashlight Mount
$75.00
|
|
Sign
Up To Our Mailing List.
|
|
|
